White-Westinghouse ES200 Servisní příručka

1White-Westi nghouseELECTROLUX HOME PRODUCTS NORTH AMERICASERVICE MANUALNEXT GEN30” ELECTRICFREESTANDING RANGES5995361523December 20011111111

10Quick reference sheet1. Serial number breakdown:2. Oven sensor resistance chart:3. Element resistanceRTD SCALE Temperature Degrees F. R

11Maximum allowable surface temperatures for gas & electric cooking products:When Frigidaire tests side panels and doors for surface temperature,

12INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.Clearances and Dimensi

13• 5/16" Nutdriver or Flat Head Screwdriver• Electric Drill & 1/8" Diameter Drill Bit (MasonryDrillBit if installing in concrete)For el

14B. Drill Pilot Holes and Fasten Bracket - Drill a 1/8"pilot hole where screws are to be located. If bracketis to be mounted to the wall, drill

15Mobile home installations, new branch circuitinstallations (1996NEC) or areas where local codes donot permit grounding through neutral require a fou

16GROUNDING INSTRUCTIONS:A ground strap is installed on this range which connectsthe center terminal of the terminal block (neutral) to thechassis. Th

17Model and Serial Number LocationThe serial plate is located on the right-hand surface of theoven front frame at the storage or warmer drawer; or the

18Element does not heat:Checking the system with a Voltmeter, if the elementdoes not heat up.1. Remove the back of the control panel toexpose the swit

19between the switch and the element are open.If the meter reads line to line voltage theelement is defective.Element does not cycle:If the element do

2ATTENTION!!!This service manual is intended for use by persons having electrical and mechanical trainingand a level of knowledge of these subjects ge

20Both elements do not heat:Checking the system with a Voltmeter, if the elementsdo not heat up:1. Remove the back panel of the backguard toexpose the

21the range, with four displays, one for each element thatshows the setting of the control. These work as interfacesbetween potentiometers and the mo

22How it operates:Whenever the range is connected to electrical power,low voltage from the mother board is applied across thetwo outside pins of the p

23Reconnect the harness, if the F5 is still displayed, go tothe right hand user interface board as viewed from therear of the range. Notice that the

24L1NL1H11A2AH2L2Indicator lightElementTroubleshooting:There are four ways a warming zone system with a stan-dard 120 VAC infinite switch can fail:1.

25Element does not cycle:If the element does not cycle when the switch is set in aposition other than high the switch is defective.Indicator light doe

26SECTION C - ELECTRONIC OVENCONTROL SYSTEMSThis section covers five electronic oven control systems.1. ES 1002. ES 2003. ES 3004. ES 4005. ES 450The

271. Press Bake and make sure the bake temperature isdisplayed.2. Press the Up Arrow or Down Arrow to increaseor decrease the set temperature.To bro

28Calibration:To check oven calibration:1. Place a thermometer or thermocouple in thecenter of the oven.2. Program the oven for bake and the temperatu

29element is defective. If the meter reads zero thewiring to the element is open.If the control appears to be operating normally but thebroil element

3TABLE OF CONTENTSSafe servicing practices 2Quick reference sheet 10Maximum allowable surface temperatures 11SECTION A - INSTALL

30SAMPLE SCHEMATIC FOR ES100 CONTROL SYSTEM

31The ES 200 Electronic Oven Control System:The ES 200 electronic oven control system is used tocontrol the oven on self-cleaning model ranges that do

32To change the minute timer while it is in use:While the timer is active and shows in the display, pressand hold the Up Arrow or Down Arrow to increa

335. Place the pan on the oven rack. Open the ovendoor to the broil stop position when broiling.6. Broil on one side until food is browned; turn and c

34provide power to the bake element once again. After thefirst cycle the preheat light is turned off and whenever theoven calls for heat, the EOC cyc

352. With an Ohmmeter measure the resistance betweenpins 12 and 13 in the plug (not on the control board).If the meter reads around the value of the o

36Oven door locks when the oven is programmedfor clean but the oven does not heat:1. If the oven operates normally in bake, replace thecontrol.Lock mo

37SAMPLE SCHEMATIC FOR THE ES 200 CONTROL SYSTEM

38The ES 300 Electronic Oven Control System:The ES 300 electronic oven control system is used tocontrol the oven on self-cleaning model ranges that do

39when the set time has run out. The minute timer can beused alone or during any of the other oven functions.When the minute timer is in use with any

4To broil 27How the ES 100 operates 27Bake 27Broil 27Calibration 28The control cannot be calibrated 28Troubleshooting 28 - 29F1 code 28F3 code 28

40before cooking begins, and should be removedpromptly when cooking is completed.BakeBroilClear OffCleanOvenPreheatDoor LockedSelf-Cleaning OvenSpeed

41the oven door is opened. The fan will continue tooperate until baking is complete.3. To cancel the Speed Bake function, press ClearOff on the oven

42On these models, the bake element is designed to betilted up using your hand from the front of the bakeelement. This will allow easier access to the

43element. After the first cycle, the preheat light is turnedoff. Then whenever the oven calls for heat the controlcycles the broil element on for s

44Troubleshooting:The ES 300 has some self diagnostics built into themicroprocessor to help in troubleshooting the system.When a failure occurs one of

45Oven door does not lock when the oven is pro-grammed for clean:1. Remove power from the range, go to the back ofthe control and disconnect the 15 pi

46SAMPLE SCHEMATIC FOR THE ES 300 CONTROL SYSTEM

47The ES 400 Electronic Oven Control System:The ES 400 electronic oven control system is used tocontrol ovens on self-cleaning model ranges with theco

48Minute timer:The minute timer serves as an extra timer in the kitchenthat will beep when the set time has run out. It does notstart or stop cooking.

49be programmed to bake at any temperature from 170° Fto 550° F (the sample below is for 350° F).To set the bake temperature:1. Arrange oven racks and

5To change the minute timer while it is in use 39To cancel the minute timer before the set time has run out 39To set the controls for baking 39To chan

504. Press 3 5 0 . “350°” will flash and “BAKE”will show in the display.5. Press Start . “350°” and “BAKE“ will show in thedisplay.6. Press C

512. Arrange oven rack and place the pan on the ovenrack. Be sure to center the broiler pan directlyunder the broil burner. Open the oven door to theb

52oven door lock will begin to close automaticallyand once the door has been locked the “DOORLOCKED” indicator light will quit flashing andremain on .

53Convection roast:Convection roast operates the same as convection bakeexcept the control does not operate above the settemperature and the temperatu

541. Disconnect the fifteen pin plug from the back of theoven control that connects the sensor to the ovencontrol.2. With an Ohmmeter, measure the res

55line to line voltage (240 VAC) the element isdefective. If the meter reads zero the wiring to theelement is open.Broil element does not heat:1. Wit

56SAMPLE SCHEMATIC FOR THE ES 400 CONTROL SYSTEM

57The ES 450 Electronic Oven Control System:.The ES 450 electronic oven control system is used tocontrol ovens on self-cleaning model ranges that have

58Minute timer:The minute timer serves as an extra timer in the kitchenthat will beep when the set time has run out. It does notstart or stop cooking.

59be programmed to bake at any temperature from 170° Fto 550° F (the sample below is for 350° F).To set the bake temperature:1. Arrange oven racks and

6To change the temperature from °F to °C or from °C to °F 48Silent control operation 48To change control from normal soundoperation to silent control

604. Press 3 5 0 . “350°” will flash and “BAKE”will show in the display.5. Press Start . “350°” and “BAKE“ will show in thedisplay.6. Press C

612. Arrange oven rack and place the pan on the ovenrack. Be sure to center the broiler pan directlyunder the broil burner. Open the oven door to theb

62To set the controls for the self-cleaning cycle tostart immediately and shut off automatically:1. Be sure the clock shows the correct time of dayand

63baking at a set time. The stop time cannot be set formore than 11 hours and 59 minutes ahead of the time ofday.Convection bake:When the convection

64the display will return to the time of day. Press ClearOff to reject the change if necessary.To adjust the oven temperature lower:1. Press the Bake

65Blank display:1. With the range connected to electrical power, go tothe back of the control and measure the voltagedrop between terminal L1 and neut

66SAMPLE SCHEMATIC FOR THE ES 450 CONTROL SYSTEM

67Warmer drawer:Warmer drawers are use to hold food at servingtemperature, usually between 160° F to 190° F.To set the warmer drawer thermostat contro

68If the element heats during preheat, then stay offuntil the temperature drops to about 130° F:1. Check the diode and the cycling portion of the warm

69SECTION D - DISASSEMBLY ANDREPLACEMENT OF PARTSNOTE: To reinstall parts, reverse all proceduresBackguardTo remove the backguard back panel:1. Disco

7Oven door locks but the oven does not heat 55Door latch is partly closed with door open 55Sample schematic for ES400 control system 56The ES 450 Elec

70Backview of potentiometer4. Remove the knob by pulling straight off.5. With a 1/2” wrench remove the holding nut byturning it counterclockwise, and

71To remove the control panel:1. Disconnect power from the range.2. Remove the back panel from the backguard.3. Remove the knobs.4. Disconnect the inf

72Ranges with coil top elements:4. Raise the front of the main top and disengagethe lift and lock rods.Coil element top lift and lock rodSmooth top ra

7311. Remove the three screws holding the oven vent coverand remove the oven vent cover.Vent cover12 Remove the two screws holding the splasher panelt

747. Pull the top forward and up.To remove the main top on smooth top ranges:1. Disconnect power from the range.2. Remove the back panel from the back

75Smooth top elements:1. Disconnect power from the range.2. Open the oven door and remove the two phillipsscrews holding the main top to the front fra

76To remove burner pan (coil element ranges only):1. Disconnect power from the range.2. Remove main top. (See main top removal)3. Remove the oven vent

77To remove oven door:1. The oven door is held to the oven door hinges by twoscrews. (One in each hinge.)2. To remove the oven door remove the two scr

78Trim screwsDoor handle:1. Remove upper door trim.2. Remove the two screws holding the door handle tothe upper door trim.Handle screwsOuter door glas

793. Pull the element into the oven and disconnect thewires.Bake element screwsBroil element:1. Disconnect power from the range.2. Remove the two scre

8To change the calibration 63To adjust the oven temperature higher 63To adjust the oven temperature lower 63Troubleshooting 64 - 65F1 code 64F3 c

80Oven vent (coil element models)Oven vent (smooth top models):1. Remove the backguard back panel and the rangeback.2. Remove the vent cover by removi

81Door latch removal (self clean):1. Disconnect power from the range.2. Models with coil top element remove the burner pan.(See burner pan removal.)3.

82Three screws4. Pull back on the assembly. Lift the rod and tip thefront of the assembly down to release the rod.5. If replacing the assembly be sur

83Oven sensor mounting screwsRemoving oven light socket:1. Disconnect power and remove back panel.2. Remove oven light shield (self-clean models) andd

84Front bodyside panel screwsStorage DrawerRemoving the storage drawer front panel:1. Remove two screws from the upper inside panel.Two inside screws2

852. Remove the side heat shield by removing four screwsholding the shield to the frame and side panel. Turnthe front leveling leg almost out and sli

86Removing drawer rail from range frame:1. Remove the screw holding the rail to the frame andpull forward on the rail.Rail screwRemoving warmer drawer

87NOTES

88

9To remove burner pan (coil element ranges only) 76Oven door 76 - 78To remove oven door seal 76To remove oven door 77Door hinge adjustment 77Remo